![]() ![]() A corner that’s only slightly greater than 90 degrees usually means you can put the back of the corner cabinet up against one wall-often the longer wall-and make up for the out-of-square condition at the back of the countertop on the short run of cabinets. If the corners are out of square, or if either of the end walls aren't plumb, you will need to adjust the location of the base cabinets. You will also use fillers or scribe at base and wall end cabinets to make up for irregularities and any slight out-of-plumb condition. You will use filler strips to make up for any spacing adjustments, and these will be noted in your design layout. If there is a sink cabinet that must center on a window, lay that out first otherwise, start at the corners and work outward. And do not stack and lean all these pieces on top of each other, or you’ll for sure be using that touch-up marker and wax fill stick you bought to fix them. Remember the cabinet coding I mentioned earlier to know which cabinet is which? now your blue tape comes in handy, put a small piece on the inside of the door or drawer, and mark the cabinet which it belongs. Most doors and drawers must be removed anyway to attach one cabinet to the other. For one, this will reduce the weight considerably, and for two, you won’t bang them up when you are installing them. One thing for sure is that you should always remove the doors and drawers from all your cabinets. Whichever you install first matters on the layout of the kitchen and the cabinets, the uncommon situations at hand and your preference. The Chicken or the egg? Uppers or lower? As a long-time debate by installers and there is no right or wrong answer. This way, it is one less thing you must worry about, and you won’t be double-checking a piece of paper constantly. For base-1 base-2 or wall-1 wall-2 and so on, then each cabinet when you get them, put a piece of blue tape on the back of each and mark the same mark and on the kitchen walls also. One trick is to mark the cabinets on the drawing b-1, b-2, w-1, w-2, etc. It doesn’t have to be detailed but just hand-drawn marks, so you know what’s going where according to your drawing, and you’ll notice if a cabinet doesn’t belong. ![]() Now label the location of all the cabinets and appliances on the wall. This way, you just put the bottom back of the cabinet on top of it, and at least you know the cabinet is level on the bottom, and even though it can fall forward, it's not slipping and sliding all over the wall. Don’t worry about holes in the wall as these you can fill before you put the backsplash up. Screws through the rail into the wall studs. Attach it by driving three or four 2 in. Use a cleat and save your back! Installing kitchen cabinets is usually a two-person project and depending on how confident you are hanging your upper cabinets or how much experience you or your helper have, you may want to screw in a temporary a 1x3 or 1x2 piece of wood as a support rail into the wall, aligning the top edge of the rail with the line for the bottom edge of the wall cabinets. The highest mark will be your high spot, make marks all around the room where the new laser line is and draw a straight line with your 6-foot level or snap a chalk line on the drywall around the room to mark the top of the base cabinets, and this is now the mark of the top back of the cabinets. If it does mark the wall at that point and raise the laser line to that mark and keep going until you go everywhere, the cabinets will be. Then I slide it along the floor against the wall and look to see if the laser drops below the line. I take a piece of scrap wood or a broom handle, put a piece of blue tape on it, and mark up 34 ½" With a black sharpie. Then measure up a mark 34 ½" Up from the floor and set the laser on that line. You will set up your laser level in the middle of the room. I am talking about one that shoots a line 360 degrees around the room. When I say laser level, I’m not talking about a straight line that comes out of a level. So, with that said the first step in laying out the cabinets is to find the high spots this is where the importance of a laser level comes into play.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |